View M54HC193K_1269985.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M54HC193
RAD-HARD SYNCHRONOUS UP/DOWN BINARY COUNTER
s s
s
s
s
s
s
s s
s
s
HIGH SPEED: fMAX=55MHz (TYP.) at VCC=6V LOW POWER DISSIPATION: ICC =4A(MAX.) at TA=25C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 193 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9204-065
DILC-16
FPC-16
ORDER CODES
PACKAGE DILC FPC FM M54HC193D M54HC193K EM M54HC193D1 M54HC193K1
DESCRIPTION The M54HC193 is an high speed CMOS SYNCRONOUS UP/DOWN BINARY COUNTERS fabricated with silicon gate C2MOS technology. The counter has two separate clock inputs, an UP COUNT input and a DOWN COUNT input. All outputs of the flip-flop are simultaneously triggered on the low to high transition of either clock while the other input is held high. The direction of counting is determined by which input is clocked. This counter may be preset by entering the desired data on the DATA A, DATA B, DATA PIN CONNECTION
C, and DATA D input. When the LOAD input is taken low the data is loaded independently of either clock input. This feature allows the counters to be used as divide-by-n counters by modifying the count length with the preset inputs. In addition the counter can also be cleared. This is accomplished by inputting a high on the clear input. All 4 internal stages are set to low independently of either COUNT input. Both a BORROW and CARRY output are provided to enable cascading of both up and down counting functions. The BORROW output produces a negative going pulse when the counter underflows and the CARRY outputs a pulse when the counters overflows. The counter can be cascaded by connection the CARRY and BORROW outputs of one device to the COUNT UP and COUNT DOWN inputs, respectively, of the next device. All inputs are equipped with protection circuits against static discharge and transient excess voltage.
April 2004
1/13
M54HC193
IEC LOGIC SYMBOLS
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN N 3, 2, 6, 7 4 5 11 12 13 14 15, 1, 10, 9 8 16 SYMBOL QA to QD CCD CCU LOAD CARRY BORROW CLR A to D GND VCC NAME AND FUNCTION Flip-Flop Outputs Count Down Clock Input Count Up Clock Input Asynchronous Parallel Load Input (Active LOW) Count Up (Carry) Output (Active LOW) Count Down (Borrow) Output (Active LOW) Asynchronous Reset Input (Active High) Data Inputs Ground (0V) Positive Supply Voltage
TRUTH TABLE
COUNT UP COUNT DOWN H H H H X X
X : Don't Care
LOAD H H H H
CLEAR L L L L L H
FUNCTION COUNT UP NO COUNT COUNT DOWN NO COUNT PRESET RESET
X X
L X
2/13
M54HC193
LOGIC DIAGRAM
This logic diagram has not be used to estimate propagation delays
3/13
M54HC193
TIMING CHART
ABSOLUTE MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 20 20 25 50 300 -65 to +150 265 Unit V V V mA mA mA mA mW C C
ICC or IGND DC VCC or Ground Current
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO Top tr, tf Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 2.0V VCC = 4.5V VCC = 6.0V Parameter Value 2 to 6 0 to VCC 0 to VCC -55 to 125 0 to 1000 0 to 500 0 to 400 Unit V V V C ns ns ns
4/13
M54HC193
DC SPECIFICATIONS
Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 VOL Low Level Output Voltage 2.0 4.5 6.0 4.5 6.0 II ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 IO=-20 A IO=-20 A IO=-20 A IO=-4.0 mA IO=-5.2 mA IO=20 A IO=20 A IO=20 A IO=4.0 mA IO=5.2 mA VI = VCC or GND VI = VCC or GND TA = 25C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 0.1 4 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.33 0.33 1 40 Typ. Max. Value -40 to 85C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 1 80 A A V V Max. -55 to 125C Min. 1.5 3.15 4.2 0.5 1.35 1.8 Max. V Unit
VIH
High Level Input Voltage Low Level Input Voltage High Level Output Voltage
VIL
V
VOH
5/13
M54HC193
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 TA = 25C Min. Typ. 30 8 7 65 20 16 40 13 11 40 13 11 85 25 20 110 30 25 110 31 25 80 25 20 120 34 28 110 30 25 100 30 25 120 35 29 120 35 29 12 48 55 34 9 7 Max. 75 15 13 190 38 32 130 26 22 130 26 22 220 44 37 250 50 43 250 50 43 190 38 32 250 50 43 250 50 43 225 45 38 250 50 43 250 50 43 4 20 24 100 20 17 125 25 21 Value -40 to 85C Min. Max. 95 19 16 240 48 41 165 33 28 165 33 28 275 55 47 315 63 54 315 63 54 240 48 41 315 63 54 315 63 54 280 56 48 315 63 54 315 63 54 3.4 17 20 150 30 26 -55 to 125C Min. Max. 110 22 19 285 57 48 195 39 33 195 39 33 330 66 56 375 75 64 375 75 64 285 57 48 375 75 64 375 75 64 340 68 58 375 75 64 375 75 64 ns ns Unit
tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (COUNT UP, DOWN - Q) tPLH tPHL Propagation Delay Time (COUNT UP CARRY) tPLH tPHL Propagation Delay Time (COUNT DOWN BORROW) tPLH tPHL Propagation Delay Time (LOAD - Q) tPLH tPHL Propagation Delay Time (LOAD CARRY) tPLH tPHL Propagation Delay Time (LOAD BORROW) tPLH tPHL Propagation Delay Time (DATA - Q) tPLH tPHL Propagation Delay Time (DATA CARRY) tPLH tPHL Propagation Delay Time (DATA BORROW) tPHL Propagation Delay Time (CLEAR -Q) Propagation Delay Time (CLEAR -CARRY) Propagation Delay Time (CLEAR BORROW) Maximum Clock Frequency Minimum Pulse Width (COUNT UP/ DOWN)
ns
ns
ns
ns
ns
ns
ns
ns
ns
tPLH
ns
tPHL
ns
fMAX
5 25 30
MHz
tW(H) tW(L)
ns
6/13
M54HC193
Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 TA = 25C Min. Typ. 34 9 7 40 12 10 30 9 7 Max. 75 15 13 100 20 17 75 15 13 0 0 0 50 10 9 50 10 9
Value -40 to 85C Min. Max. 95 19 16 125 25 21 95 19 16 0 0 0 65 13 11 65 13 11 -55 to 125C Min. Max. 110 22 19 150 30 26 110 22 19 0 0 0 75 15 13 75 15 13 ns Unit
tW(L)
Minimum Pulse Width (LOAD) Minimum Pulse Width (CLEAR) Minimum Set-up Time (DATA -LOAD) Minimum Hold Time Minimum Removal Time (LOAD) Minimum Removal Time (CLEAR)
tW(H)
ns
ts
ns
th
ns
tREM
tREM
6 2 2 14 4 3
ns
ns
CAPACITIVE CHARACTERISTICS
Test Condition Symbol Parameter VCC (V) 5.0 5.0 TA = 25C Min. Typ. 5 67 Max. 10 Value -40 to 85C Min. Max. 10 -55 to 125C Min. Max. 10 pF pF Unit
CIN CPD
Input Capacitance Power Dissipation Capacitance (note 1)
1) CPD is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC
7/13
M54HC193
TEST CIRCUIT
CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50)
WAVEFORM 1: PROPAGATION DELAY TIME, MINIMUM PULSE WIDTH (COUNT UP OR DOWN) (f=1MHz; 50% duty cycle)
8/13
M54HC193
WAVEFORM 2: PROPAGATION DELAY TIME, MINIMUM PULSE WIDTH (CLEAR, LOAD) (f=1MHz; 50% duty cycle)
WAVEFORM 3: SETUP AND HOLD TIME (A, B, C, D to LOAD) (f=1MHz; 50% duty cycle)
9/13
M54HC193
WAVEFORM 4: MINIMUM REMOVAL TIME (COUNT UP OR DOWN TO CLEAR) (f=1MHz; 50% duty cycle)
WAVEFORM 5:MINIMUM REMOVAL TIME (COUNT UP OR DOWN TO LOAD) (f=1MHz; 50% duty cycle)
10/13
M54HC193
DILC-16 MECHANICAL DATA
mm. DIM. MIN. A a1 a2 B b b1 D e e1 e2 e3 F I K L 10.90 1.14 17.65 7.62 7.29 2.1 3.00 0.63 1.82 0.40 0.20 20.06 7.36 0.45 0.254 20.32 7.62 2.54 17.78 7.87 7.49 17.90 8.12 7.70 3.83 12.1 1.5 0.429 0.045 0.695 0.300 0.287 0.88 TYP MAX. 2.71 3.70 1.14 2.39 0.50 0.30 20.58 7.87 MIN. 0.083 0.118 0.025 0.072 0.016 0.008 0.790 0.290 0.018 0.010 0.800 0.300 0.100 0.700 0.310 0.295 0.705 0.320 0.303 0.151 0.476 0.059 0.035 TYP. MAX. 0.107 0.146 0.045 0.094 0.020 0.012 0.810 0.310 inch
0056437F
11/13
M54HC193
FPC-16 MECHANICAL DATA
mm. DIM. MIN. A B C D E F G H L M N 0.38 6.0 18.75 0.33 0.38 4.31 22.0 0.43 6.75 9.76 1.49 0.102 8.76 0.127 8.89 1.27 0.43 0.48 0.015 0.237 0.738 0.013 0.015 0.170 0.867 0.017 TYP 6.91 9.94 MAX. 7.06 10.14 1.95 0.152 9.01 MIN. 0.266 0.384 0.059 0.004 0.345 0.005 0.350 0.050 0.017 0.019 TYP. 0.272 0.392 MAX. 0.278 0.399 0.077 0.006 0.355 inch
F
G
D
H
16
9
A
N
L
1
8
H
E
M
C
B
0016030E
12/13
M54HC193
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com
13/13

▲Up To Search▲

Price & Availability of M54HC193K

	To Download M54HC193K Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .